Expert Answers about Chevrolet Car Audio

• Can Jensen USB Interface and Auxiliary Audio Input Jack JENAUX Charge USB Devices
• Jensen USB Interface and Auxiliary Audio Input Jack item # JENAUX does not deliver DC to charge a device's battery. In this item the USB provides only the connectivity for playing back audio from an external USB storage device. For a product that allows USB battery charging for your devices you can use the Scosche ReVolt Car Charger - Dual Illuminated USB Ports - 12 Watt # 332-USBC242M with 2 charging ports. This plugs into a standard 12V power outlet like those in vehicles. We also offer...
  view full answer...


• No Audible Alert in RV after Depressed Brake Pedal on Roadmaster InvisiBrake
• I called my technical support contact at Roadmaster and they informed me that it is likely that you have just switched the wires that go to both the LED monitor and audio board on the Roadmaster InvisiBrake Supplemental Braking System part # RM-8700. I would first try to switch the wires to see if that fixes your problem. If that doesn't work then you will want to inch forward a bit and hold the brake pedal to see if the alarm sounds. If neither of these options work then you would need...
  view full answer...


• Can a Backup Camera Audio Be Hooked Up To the Jensen RV Stereo JDVD1500
• The Jensen RV Stereo # JDVD1500 is one of the more basic stereo units we have to offer and I believe you will be happy with it. You already noted that it is a single DIN and has the AUX and Bluetooth capabilities like what you're wanting. If your backup camera uses AV connections for the audio then yes, you could play the audio from your camera through your sound system, however the screen is a simple LCD display and wouldn't take on the functions of a monitor for your camera. This unit...
  view full answer...


• Recommended Replacement for Jensen VR209TP RV Stereo
• The Jensen Touch Screen RV Stereo part # JWM60A is our best replacement for the Jensen VR209TP Stereo which is now discontinued. They are both double din units so the cutouts should be similar making for an easy install. In regards to the wiring, it will not be the same but I have attached the pin out of the new stereo below. If you don't feel comfortable making a few wiring connections you should be able to take the unit to any local car audio shop and they would be able to make the...
  view full answer...


• Pre-Collision Avoidance Error On 2017 Toyota Highlander with Trailer Brake Controller
• The pre-collision avoidance error with an aftermarket brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 installed on a 2017 Toyota Highlander is a known issue. It's caused by back feed on the stop light switch circuit from the brake controller which is the red wire coming from the back of the unit. In order to fix this you will simply need to install a 1 amp diode in-line on this circuit which you should be able to obtain locally from an electronics or...
  view full answer...


• Installing Monitor Circuit for InvsiBrake System Through Umbilical Connecting Motorhome and Vehicle
• The Roadmaster InvisiBrake would be installed per the procedure mentioned on page 14-15 of the installation instructions that I've linked for you. Usually, you'd just use the single wire umbilical included with the kit. You could simply zip tie this extra wire to the umbilical you purchased. If you wish, you could eliminate the umbilical, and simply wire the circuit using an unused circuit in your coiled cord you just purchased. You'd need to cut the plug off the car and the motorhome end...
  view full answer...


• How To Wire a 5th Wheel for Triple Towing a Trailer with Brakes
• It is possible to triple tow (1 tow vehicle + 2 trailers) when both trailer's have brakes but this would mean that the brake output wire that runs from the brake controller in the tow vehicle to both trailers would need to be at least a 6 gauge at the minimum so you don't have issues with voltage drop. Also, the number of braked axles cannot exceed what your brake controller is capable of handing which most are usually four. In order to obtain the needed length of 6 gauge or greater wire...
  view full answer...


• Trailer Hitch Installation, Support Strap and 2 Bike Rack for a 1990 Mazda Miata
• The Curt Trailer Hitch Support Strap, # 18050, is a strap that is designed to wrap around a bike rack or cargo carrier and helps to provide extra support to the receiver when carrying hitch mounted bike racks and cargo carriers. There is a rubber coated hook on one end of the strap that will hook into the trunk or hatch lip, the other end loops around the rack or carrier and the cam buckle is used to take up slack in the strap. The tie down brackets on your Miata do not have to be removed....
  view full answer...